AVR Programmer with OLED Display and Rotary Encoder
This PCB hosts an Arduino Pro Micro via 0.1 inch header sockets (so it can be removed and used in other projects too).
There are more female sockets to connect Dupont wires to a target AVR chip for programming, or optional daughter plug-in cards can be made with chip sockets for plugging in directly.
The board is powered by the USB connector on the Pro Micro and there is a 12 volt High Voltage power supply for fuse programming.
There is an OLED and a rotary encoder on board to allow stand alone programming of fuses based on the sketch that is in the Pro Micro. By default it was designed to provide some shortcuts to change the Reset pin on ATTiny85 back and forth between a GPIO and a normal Reset pin.
When connected to a computer, if the Pro Micro contains the Arduino ISP sketch, the board can act as an ISP programmer.
Other AVR programming modes will be implemented over time. By using the headers to connect to the target device off-board, more flexibility is available to support more devices and protocols in the future.
https://youtu.be/EKmn9WPrbVk
AVR Programmer with OLED Display and Rotary Encoder
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(2)
- Likes(1)
- Engineer Feb 26,2024
- 6 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
6design
-
7usability
-
5creativity
-
7content
-
7design
-
8usability
-
9creativity
-
8content
-
7design
-
7usability
-
6creativity
-
6content
-
8design
-
7usability
-
7creativity
-
5content
-
8design
-
7usability
-
8creativity
-
7content
-
7design
-
10usability
-
9creativity
-
6content
More by Gadget Reboot
- Op Amp Buffer with In/Out Guitar Jacks The pcb has a guitar input and output jack to easily connect to a breadboard for guitar effect circu...
- 16 Channel Audio Loop Switcher This is a 16 channel audio loop switcher with 16 inputs and 16 outputs.Analog signals within a +/- 5...
- 16 Switches to RS485 Output Commands Up to 16 switches or 5v/gnd logic inputs can be monitored and when asserted (input = gnd), a sketch ...
- MCP42100 Digital Pot Breakout PCB This breakout board for the MCP42100 dual digital pot has headers that are spaced for breadboard com...
- Power Supply DC Jack/Screw Term/0.1" Header Breakout with PTC This breakout board allows connecting a power source via 2.1x5.5mm DC jack, 7.62mm screw terminals, ...
- 16x16 Analog Switch This 16x16 analog crosspoint switch uses two MT8816 8x16 switch ICs cascaded for a larger matrix.The...
- Line Level Stereo Input to 3 Stereo Output Sharing PCB This audio sharing board will take a stereo line input from a 3.5mm jack, buffer it and send it out ...
- MIDI Breakout In/Out/Thru This MIDI breakout board has 5 pin DIN jacks and Type A configured 3.5mm TRS jacks for Midi In, Midi...
- Tandy CoCo Joystick Adapter - Use Digital Inputs for Analog X,Y axis Use 5v/GND digital signals to control the analog joystick input of a Tandy Color Computer.When input...
- GPIO Addressable LED Indicators This pcb can read 8 digital inputs and display their high/low state on one of 8 addressable LEDs as ...
- Guitar Stomp Switch and LED Breakout Board This PCB takes a 9 pin 3PDT guitar effect on/off stomp switch along with an LED and resistor, and pr...
- HV5222 Breakout Board HV5222 32 bit high voltage shift register breakout boardThe driver chip has open drain outputs that ...
- DTMF Decoder 3.3v MT88L70 This DTMF decoder uses the MT88L70, powered by 3.3v and interfacing with 3.3v GPIO to decode the tou...
- PT2399 Echo IC Breakout Board The PT2399 is a low-fi echo IC with built in ADC, Ram, and DAC.It uses a handful of external resisto...
- CD4040 Binary Counter Breakout PCB Dual 4040 12 bit ripple carry binary counters.Two surface mount counters on a breakout board that fi...
- 555 Adjustable Duty Cycle and Frequency Easy to use 555 oscillator with potentiometers to adjust duty cycle and frequency.The 5 pin header c...
- DMX RS485 to TTL Isolated Adapter with 3 pin XLR This pcb can be assembled as either a DMX transmitter or receiver interface (the BOM is set up to bu...
- Phone Line Simulator (POTS Land Line) Plug an old land line phone or other device into the RJ11 jack, pick up the phone and hear a dial to...
-
Commodore 1551 Drive Cartridge Replacement
98 0 2 -
RCMHardwareByte-v2.3
84 0 0 -
Terminal Curiosity PCB Ruler
275 0 0 -
(DIY) COMMODORE 64 DEAD-TEST (781220) DIAGNOSTIC CARTRIDGE
338 0 2 -
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 3D Printable Case
377 0 0 -
Creative Micro Designs Inc. CMD FD-2000 / FD-4000 Metal Case
541 0 0 -
-